DIY bootie drier

Forum dedicated to tips and tricks for new riders and veterans alike.

DIY bootie drier

Postby weston5 » Sat Feb 01, 2014 6:42 pm

There might be wind later this week, but it'll be chilly. What could be worse than putting on cold wet booties?? Better fix that. This is how I did it:

Ingredients

    1 Sterilite 6 qt. plastic storage container ($1.99 @ Home Depot)
    1 80mm computer case fan ($6.99 @ Best Buy)
    1 110v AC to 12v DC power adapter (mega expensive at Radio Shack, get it from http://goo.gl/Xumklz)
    ~4 feet of 3/4" diameter PVC
    waterproof caulk
    soldering iron
    solder
    electrical tape
    xacto knife
    drill
    a sharpie

Instructions

The storage container you want looks like:
WESTONT-SURFACE - WIN_20131214_134504.JPG
WESTONT-SURFACE - WIN_20131214_134504.JPG (172.88 KiB) Viewed 3624 times


Start by cutting a hole in the side of the storage container for the case fan. Hold the case fan up against the side, trace it with the sharpie, then use the xacto knife or scissors to cut a hole in the side that the fan will sit snugly in. It can be crude.
WESTONT-SURFACE - WIN_20131214_134442.JPG
WESTONT-SURFACE - WIN_20131214_134442.JPG (148.13 KiB) Viewed 3624 times


Fit the fan in there snugly and make sure to feed the wires through one of the screw holes in the fan. Also be sure to make sure the fan is blowing INTO the box (there should be an arrow indicating flow direction on the rim of the fan).

Now cut the PVC pipe into 4 equal length pieces. Use your best judgement on how long to make them, they should be tall enough to suspend your bootie. You could probably also use something other than PVC just fine.

Take a piece of PVC and trace it's diameter on the plastic lid of the box with the sharpie in 4 corners of the lid. Cut out the holes with the xacto knife, the PVC tubes will sit vertically in these. Now take the caulk and do the entire inner rim of the lid and close the box on it to make a good seal.
WESTONT-SURFACE - WIN_20131214_150508.JPG
WESTONT-SURFACE - WIN_20131214_150508.JPG (143.32 KiB) Viewed 3624 times


WESTONT-SURFACE - WIN_20131214_150824.JPG
WESTONT-SURFACE - WIN_20131214_150824.JPG (158.94 KiB) Viewed 3624 times


While the lid is drying, caulk the fan into place as well. Goop it on there and make a good seal. Leave this overnight. The next morning, just mount your PVC pipe, solder up the power supply to the fan, and enjoy!
Attachments
WESTONT-SURFACE - WIN_20131214_134518.JPG
WESTONT-SURFACE - WIN_20131214_134518.JPG (158.92 KiB) Viewed 3624 times
Last edited by weston5 on Sun Feb 02, 2014 12:27 pm, edited 1 time in total.
weston5
 
Posts: 162
Joined: Sun Oct 16, 2011 3:42 pm

Re: DIY bootie drier

Postby Sark » Sat Feb 01, 2014 7:02 pm

Holy crap MacGyver. Nice work!
RRD Posse
User avatar
Sark
Captain Obvious
 
Posts: 604
Joined: Thu Jan 28, 2010 10:00 am
Location: cloud 9

Re: DIY bootie drier

Postby Salmonslayer » Sat Feb 01, 2014 8:28 pm

Simple, functional, off the shelf parts and inexpensive :wav:
'08 Nemesis HP 10m, 12m, 14m
'12 Naish Parks 5m, 7m, 9m
'13 149 MTH Custom
'14 135 Brokite Hybrid
Jailbird Rashie by Neil Pryde
'13 Engine Harness
Q-Powerline
Carkeek Swim Team distance swim specialist
User avatar
Salmonslayer
Tacoma Fanboy
 
Posts: 2743
Joined: Sat Jun 20, 2009 12:07 am

Re: DIY bootie drier

Postby C.J. » Sat Feb 01, 2014 11:20 pm

How much did it cost?

Sent from my SGH-M919 using Tapatalk 2
User avatar
C.J.
Officer of Bad Ideas, Mayor of Warshentowkneean
 
Posts: 4504
Joined: Thu Dec 18, 2008 10:39 am
Location: Edmonds

Re: DIY bootie drier

Postby weston5 » Sun Feb 02, 2014 1:38 am

~$15 with the power adapter
weston5
 
Posts: 162
Joined: Sun Oct 16, 2011 3:42 pm

Re: DIY bootie drier

Postby jason » Tue Feb 04, 2014 11:47 am

any thoughts on adding a 45* angle and another few inches of pipe so as to keep the shape of the ankle? Probably would add another $1.36 to the cost, but if you have some neoprene socks that don't stand up on their own, it would be nice.
User avatar
jason
 
Posts: 2400
Joined: Thu Sep 20, 2007 7:25 am

Re: DIY bootie drier

Postby weston5 » Tue Feb 04, 2014 1:05 pm

That would definitely help. Home Depot also has flexible vinyl tubing that you could drill holes in and actually thread through the whole sock. I kinda wish I'd bought those instead.
weston5
 
Posts: 162
Joined: Sun Oct 16, 2011 3:42 pm

Re: DIY bootie drier

Postby royce » Tue Feb 04, 2014 2:06 pm

How long does it take to dry wet booties?
User avatar
royce
 
Posts: 163
Joined: Mon Sep 12, 2011 12:55 pm

Re: DIY bootie drier

Postby weston5 » Tue Feb 04, 2014 2:08 pm

I usually place the fan intake near my electric heater output. That will do it in 3 hours. On just room temp air, it takes about a day.
weston5
 
Posts: 162
Joined: Sun Oct 16, 2011 3:42 pm

Re: DIY bootie drier

Postby Tuna » Fri Feb 07, 2014 9:48 pm

nice little project there.
you can pickup a cheap ac to dc converter locally at goodwill for $0.99 or $1.99
if it plugs into the wall and has a black box, it is converting power
look at the fine print for the output voltage (amperage should not be an issue)

long time no posty... ;)
Have you tugged your kite today?
User avatar
Tuna
I make heavy things float
 
Posts: 1162
Joined: Sat Feb 16, 2008 6:47 pm
Location: In a boat, down by the river

Next

Return to Tips and Tricks

Who is online

Users browsing this forum: No registered users and 1 guest